Imágenes de páginas
PDF
EPUB

or an increase of 50 per cent. This represents the increase of

pressure to be dealt with in the fastest of our cruisers as compared

[blocks in formation]

as the square of the speed, so that, comparing 24 knots with 19 knots, the proportion of pressure for equal areas is (24)=1.5,

[graphic]

with our fastest battle-ships. If, therefore, we fitted a rudder hinged on the forward edge in a cruiser, the steering gear would need to be very massive, the steering engine would have to be of large power, and steering by hand would be difficult. On these accounts the rudders of cruisers are always balanced, so that the moment of the water pressure about the rudder-head is small even at high speeds.

The weight of the rudder is taken by the top of the sternpost, as shown in Fig. 77. At the top of the rudder-head a recess is formed, into which a bearing is placed in two halves. This bearing rests on the rudder cross-head, which has three or four legs. These are connected to a circular bearing ring, which slides in the metal path on the top of the sternpost.

WATER

PRESSURE

HEAD OF

STERN POST

PRESSURE

WATER

-HEAD OF

STERN POST

SUPPORT OF
PINTLE

Fig. 79 shows in some detail the construction of the sternpost and rudder of a large cruiser.

In determining the diameter of the rudder-head of an unbalanced rudder, we practically have only the twisting to deal with, but in cruisers the bending is of large amount, while the twisting going ahead is only small. Figs. 80 and 81 show how the two forms of balanced rudder would bend supposing each is held rigidly in the sternpost. In the first case it is like a beam held at one end and simply supported at the other. In the second case it is held at one end and supported near the middle, with the other end free. In either case a considerable force has to be taken by the lower pintle, and a large bending moment at the rudder-head. The condition going astern has to be investigated, as it may happen that this is the worst case. The maximum speed astern is assumed to be about three-fourths the full speed ahead. The centre of pressure then is nearer the after edge, and the twisting moment about the axis is of considerable amount. This twisting moment, combined with the

SUPPORT

OF PINTLE

FIG. 80.

FIG. 81.

bending moment, will determine the necessary size for the rudder-head, unless the ahead conditions require a larger diameter.

In any rudder, the head being under water, it is necessary that the hole in the sternpost should be made watertight. The hole is lined with gunmetal, and the rudder-head is cased with a gunmetal sleeve, as shown in Figs. 69 and 77. A stuffing gland is fitted at the top to make the hole watertight.

Projections are cast on the rudder on each side to bring up against the sternpost when the rudder is hard over; these, however, are being omitted in some recent ships.

It was formerly the practice to supply each ship with a mould giving the actual shape of the rudder. It is the present practice to supply a sketch of the

rudder on a large scale, giving complete figured dimensions.

Shaft Brackets.-In twin screw vessels a considerable length of the propeller shafting is outside the ship, and brackets are fitted on either side, just forward of the propellers, to take the weight of the after end of the shafting,

etc. For steel ships the brackets are of cast steel, for sheathed ships of phosphor bronze. These brackets do not have to take any fore-and-aft thrust (this

[blocks in formation]

being taken in the engine-room by the thrust block), but they have to bear the very considerable weight of the propeller, etc. Because of this the attachment to the structure of the ship has to be very

secure.

Fig. 82 shows the arrangement in a recent battle-ship. The arms are flattened out at the top and bottom. The upper palm passes inside the ship, where it is riveted to a thick fore-and-aft plate. The lower palm is shaped with a scarph to fit a corresponding scarph on the other bracket. The two brackets are then

securely fastened to the 2-in. fore-and-aft plate, and to the forward end of the sternpost casting (see also Fig. 70). The arms of the brackets are of pear-shaped section, with the blunt end foremost. This is in order to diminish the resistance of these brackets, it having been proved by experiment that this form offers the least resistance when fully submerged. (It will be remembered that a torpedo has a blunt nose and a fine run.)

CHAPTER VIII.

STEERING GEARS.

THE steering gear, fitted at the stern adjacent to the rudder, is a most important fitting of a war-ship, and, except in the smallest classes, is always arranged under water and under protection. The stern has to be specially shaped to do this, and Figs. 71 to 76 show how this is done in different classes of ships. Under ordinary circumstances the steering gear is actuated by the steam steering engine, but hand wheels are provided as an auxiliary.

The twisting moment on the rudder-head (within the ordinary limits, viz. up to about 35°), which has to be overcome by the steering gear, depends on

(i.) The area of the rudder;

(ii.) The square of the speed of the water meeting the rudder; (iii.) The angle made by the rudder with the middle line, and (iv.) The distance of the centre of pressure from the axis. This last is of great importance, and has led to the introduction of balanced rudders, as Figs. 71 to 74, because in these rudders the centre of pressure is close to the axis. This makes the twisting moment small, even at high speeds.

The larger the angle (within the ordinary limits) the greater is the moment to be dealt with. A gear which, with a constant motive force, will operate on a rudder to overcome a large twisting moment at large angles, and a small moment at small angles, will be the most desirable. This is necessarily accompanied by a slower motion at large angles than at small angles. Such a steering gear is termed compensating. We shall consider three such gears, which have been largely fitted in vessels of the Royal Navy.

1. Rapson's Slide Steering Gear.-This gear is shown in outline in Fig. 83, and in some detail in Fig. 84. It is a very heavy gear, and takes up a lot of room. It has been principally

« AnteriorContinuar »